Matek CRSF To PWM Converter CRSF-PWM-6

 Matek's Industry first CRSF to PWM (Crossfire to Servo) protocol converter adapter boards.
The Matek CRSF-PWM-6 has 6 PWM servo outputs. Has integrated voltage sensor and external current sensor can be connected. PWM output frequency can be adjusted for faster servos (50Hz default, 100, 160, 330, 400Hz)

Check out our ExpressLRS Collection, all our Receivers and the rest of our Matek products!

Specifications:

• Compatible with CRSF protocol receiver only
• 6x PWM outputs
• PWM frequency configurable (50Hz default, 100,160,330, 400Hz)
• 2x UARTs (for Receiver and GPS)
• Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats
• 36V Max. battery voltage sense (1K:10K voltage divider built-in)
• Compatible with external Current sensor (0~3.3V)
• Vbat and Current sensor scale configurable
• Failsafe value auto set
• Firmware upgradeable
• Rated voltage: 4~9V @5V pad, 0~36V @Vbat, 0~3.3V @Curr
• No 5V regulator built-in
• 25mm x 16mm, 1.3g
• Packing: 1x CRSF-PWM-6, Dupont 2.54 pins

Pinouts and Pads

• Tx1/Rx1(UART1) for CRSF protocol Receiver
• Tx2/Rx2(UART2) for GPS/firmware update/setting parameters
• 1~10: CH1~CH10 PWM outputs
• Curr: current sensor signal (0~3.3V)
• Vbat: Battery voltage sensing (0~36V)
• G: ground
• 4v5 pad voltage = 5V pad voltage -0.3V,  make sure the voltage on 5V pad is not higher than receiver and GPS rated voltage.

Failsafe

• Failsafe value is set automatically after CRSF-PWM board is powered on and receive CRSF signal. LED blinks 8 times quickly.
• Failsafe value = The PWM value of each channel(except CH3) when CRSF signal is received by CRSF-PWM board for the first time
• CH3 is specially arranged for the throttle,  Failsafe value = 988 by default.
• Usually put the Throttle  joystick to the lowest point,  put AIL(Roll), ELE(Pitch), RUD(Yaw) middle before powering on receiver.

LED status

• slow blinks: CRSF-PWM board doesn’t receive CRSF signal, e.g., receiver is not bound with transmitter, receiver is not connected to UART1 of CRSF-PWM board.
• 8x quick blinks: CRSF-PWM board received CRSF signal and failsafe value is saved.
• solid ON:  CRSF-PWM board and receiver are working normally
• 2x slow blinks between 8x fast blink and solid on: CLI mode is active

GPS telemetry

• Compatible with GPS NMEA protocol
• GPS “TX” to CRSF-PWM board “RX” Single wire half duplex UART connection,   CRSF-PWM board “TX” to GPS “RX” is not essential.
• Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Sats
• u-blox series GPS can output “0+1 – UBX+NMEA” protocol by default
• Sensors(GPS, GSpd, Hdg, Alt, Sats) will blink in Transmitter TELEMETRY tab once CRSF-PWM board has connection with GPS.
• Troubleshooting for no GPS telemetry,  double check the wiring between GPS and CRSF-PWM board,  some u-blox GPS may don’t output NMEA protcol, you need to be reverted GPS to default configuration in u-center.
• with OpenTX Telemetry Logging, You can plot your flight path or search the lost plane.

TIM & PWM Frequency

• PWM frequency on all 10x Channels can be configured according to TIM
• PWM run at 50Hz by default
• TIM2:  CH1, CH2, CH4
• TIM16: CH3
• TIM3:  CH5, CH6, CH7, CH8
• TIM1:  CH9, CH10

CLI mode

• If CRSF-PWM board doesn’t detect GPS connected to UART2 within 10 seconds after powering on,  CLI mode will active.
• After CLI mode is active, CRSF-PWM board can be connected to configurator via USB-TTL module/FC passthrough.
• in CLI mode, CRSF-PWM board firmware can be updated
• CLI mode has no effect to receiver CRSF signal and PWM outputs

Includes

• 1 x CRSF-PWM-6 Converter
• 1 x Dupont 2.54 pins